From f0839d9fdd9dc74eef0eafc5562fabf9d7259f08 Mon Sep 17 00:00:00 2001
From: 천호석 <hosuk1418@naver.com>
Date: 수, 14 12월 2022 17:46:40 +0900
Subject: [PATCH] 1. Laser on 시 Stage position도 같이 확인 하도록 변경. 2. Auto power 측정, Manual power 측정 전후 Scanner Z 축 대기 위치 이동 하도록 수정 3. 프로그램 종료 시 Laser off 하도록 수정. 종료 대기시간 5sec
---
SHARP_CLAS_UI/500.Equipment/700.Unit/000.Loader/LoaderLiftOut.cs | 32 ++++++++++++++++++++++++++++++--
1 files changed, 30 insertions(+), 2 deletions(-)
diff --git a/SHARP_CLAS_UI/500.Equipment/700.Unit/000.Loader/LoaderLiftOut.cs b/SHARP_CLAS_UI/500.Equipment/700.Unit/000.Loader/LoaderLiftOut.cs
index cc0066b..bbe5f51 100644
--- a/SHARP_CLAS_UI/500.Equipment/700.Unit/000.Loader/LoaderLiftOut.cs
+++ b/SHARP_CLAS_UI/500.Equipment/700.Unit/000.Loader/LoaderLiftOut.cs
@@ -303,6 +303,18 @@
{
Alarm_Manager.Instance.Occurred(En_Alarm_List.AL_0130_LD_TRAT_OUT_LIFT_Z_POWER_OFF);
}
+ else if (IsLiftInSensor1 || IsLiftInSensor2)
+ {
+ Interlock_Manager.Add_Interlock_Msg("Loader Lift empty", "Home can't run, Lift in sensor detected.");
+ }
+ else if (IsLiftLimitSensor1 || IsLiftLimitSensor2)
+ {
+ Interlock_Manager.Add_Interlock_Msg("Loader Lift empty", "Home can't run, Lift limit sensor detected.");
+ }
+ else if (Clamper.ClampSol)
+ {
+ Interlock_Manager.Add_Interlock_Msg("Loader Lift empty", "Home can't run, Clamp is clamped ");
+ }
else
{
_homeStep = LiftHomeSteps.S1100_CONVEYOR_HOME_CHECK;
@@ -359,7 +371,22 @@
}
else
{
- _homeStep = LiftHomeSteps.S1300_MOVE_STAY_POSITION;
+ if (equipment.loader.ConveyorOut.IsLiftInSensor || equipment.loader.ConveyorOut.IsLiftInCompleteSensor)
+ {
+ if (equipment.loader.ConveyorOut.IsLiftInSensor)
+ {
+ Alarm_Manager.Instance.Occurred(En_Alarm_List.AL_0592_LD_TRAY_OUT_CONVEYOR_LIFT_IN_SENSOR_CHECK);
+ }
+
+ if (equipment.loader.ConveyorOut.IsLiftInCompleteSensor)
+ {
+ Alarm_Manager.Instance.Occurred(En_Alarm_List.AL_0593_LD_TRAY_OUT_CONVEYOR_LIFT_IN_COMPLETE_SENSOR_CHECK);
+ }
+ }
+ else
+ {
+ _homeStep = LiftHomeSteps.S1300_MOVE_STAY_POSITION;
+ }
}
break;
}
@@ -1100,6 +1127,8 @@
{
if (IsStayPosition)
{
+ _trayCount = 0;
+
if (equipment.loader.ConveyorOut.IsLiftInSensor || equipment.loader.ConveyorOut.IsLiftInCompleteSensor)
{
Step = LiftOutSteps.S2420_CONVEYOR_UNLOAD;
@@ -1128,7 +1157,6 @@
{
if (equipment.loader.ConveyorOut.IsWorkEnd)
{
- _trayCount = 0;
if (equipment.cim_mode == En_Cim_Mode.Online)
{
Step = LiftOutSteps.S2500_PORT_STATUS_CIM_SEND;
--
Gitblit v1.9.3